摘要Indium tin oxide (ITO) films were prepared by rf magnetron sputtering under two conditions: (i) at substrate temperature Ts from room temperature (RT) to 350°C, (ii) with additional post−annealing in vacuum at 400°C for 30 min in comparison of their crystalline structures, and electrical−optical properties of the films deposited. From the experimental results, it is found that, under the first condition, the crystalline structures and the electrical-optical properties of the films are improved with the increasing Ts. Under the other condition, i.e. with the additional post−annealing, the films exhibit higher degree of crystallinities and better electrical-optical properties. Under the two deposition conditions, inter-relation between electrical-optical properties and the crystalline structure is observed clearly. However, even under the same annealing condition, it is observed that improved properties of the films are different, depending on their deposition temperatures, which implies that an initial stage of the ITO film before annealing is an important factor for the film's properties improved after annealing. The resistivity of 2.33×10-4 Ω⋅cm can be achieved at Ts of 350°C after annealing.
Abstract：Indium tin oxide (ITO) films were prepared by rf magnetron sputtering under two conditions: (i) at substrate temperature Ts from room temperature (RT) to 350°C, (ii) with additional post−annealing in vacuum at 400°C for 30 min in comparison of their crystalline structures, and electrical−optical properties of the films deposited. From the experimental results, it is found that, under the first condition, the crystalline structures and the electrical-optical properties of the films are improved with the increasing Ts. Under the other condition, i.e. with the additional post−annealing, the films exhibit higher degree of crystallinities and better electrical-optical properties. Under the two deposition conditions, inter-relation between electrical-optical properties and the crystalline structure is observed clearly. However, even under the same annealing condition, it is observed that improved properties of the films are different, depending on their deposition temperatures, which implies that an initial stage of the ITO film before annealing is an important factor for the film's properties improved after annealing. The resistivity of 2.33×10-4 Ω⋅cm can be achieved at Ts of 350°C after annealing.
(Treatment of materials and its effects on microstructure, nanostructure, And properties)
引用本文:
N. Boonyopakorn;N. Sripongpun;C. Thanachayanont;S. Dangtip;. Effects of Substrate Temperature and Vacuum Annealing on Properties of ITO Films Prepared by Radio-Frquency Magnetron Sputtering[J]. 中国物理快报, 2010, 27(10): 108103-108103.
N. Boonyopakorn, N. Sripongpun, C. Thanachayanont, S. Dangtip,. Effects of Substrate Temperature and Vacuum Annealing on Properties of ITO Films Prepared by Radio-Frquency Magnetron Sputtering. Chin. Phys. Lett., 2010, 27(10): 108103-108103.
[1] Castro-Rodríguez R et al 2000 Appl. Surf. Sci. 161 340
[2] Chung C H et al 2005 Thin Solid Films 491 294
[3] Hsu C M et al 2005 Thin Solid Films 474 19
[4] Yoo K S et al 2005 Sensors and Actuators B 108 159
[5] Ota R et al 2003 Surf. Coat. Technol. 169-170 521
[6] Purica M et al 2007 Thin Solid Films 515 8674
[7] Sawada Y, Kobayashi C, Seki S and Funakubo H 2002 Thin Solid Films 409 46
[8] Frank G and Köstlin H 1982 Appl. Phys. A 27 197
[9] Bhatti M T et al 2004 Mater. Chem. Phys. 84 126
[10] Terzini E, Nobile G, Loreti S, Minarini C, Polichetti T and Thilakan P 1999 Jpn. J. Appl. Phys. 38 3448
[11] Cruz L R et al 2004 Mater. Res. Bull. 39 993
[12] Sato Y, Taketomo M, Ito N, Miyamura A and Shigesato Y 2008 Thin Solid Films 516 4598
[13] Gassenbauer Y and Klein A 2004 Solid State Ionics 173 141
[14] Park J O, Lee J H, Kim J J, Cho S H and Cho Y K 2005 Thin Solid Films 474 127
[15] Antony A, Nisha M, Manoj R and Jayaraj M K 2004 Appl. Surf. Sci. 225 294
[16] Yang C H et al 2006 Mater. Sci. Engin. B 129 154
[17] Meng L J and dos Santos M P 1996 Thin Solid Films 289 65
[18] Hu Y, Diao X, Wang C, Hao W and Wang T 2004 Vacuum 75 183
[19] Meng L J and dos Santos M P 1998 Thin Solid Films 322 56
[20] Park J O, Lee J H, Kim J J, Cho S H and Cho Y K 2005 Thin Solid Film 474 127
[21] Mergel D, Stass W, Ehl G and Barthel D 2000 J. Appl. Phys. 88 2437
[22] Lee K H et al 2004 J. Appl. Phys. 95 586
[23] Jung Y S, Lee D W and Jeon D Y 2004 Appl. Sur. Sci. 221 136
[24] Sato Y, Taketomo M, Ito N and Shigesato Y 2008 Thin Solid Films 516 5868
[25] Nisha M, Anusha S, Antony A, Manoj R and Jayaraj M K 2005 Appl. Surf. Sci. 252 1430
[26] Benamar E, Rami M, Messaoudi C, Sayah D and Ennaoui A 1999 Solar Energy Materials and Solar Cells 56 125
[27] Lee H C and Park O O 2004 Vacuum 75 275
[28] Lee H C and Park O O 2004 Vacuum 77 69
[29] Hamberg I, Granqvist C G, Berggren K F, Sernelius B E and Engström L 1984 Phys. Rev. B 30 3240
2010, Vol. 27 
